The correct size jets are the ones that make it run right.
There are no jetting chart that covers all the possible intake and exhaust combinations. It's up to the mechanic modifying the systems to re-jet (usually by trial and error) for the best performance. Changes to the intake affect jetting more than changes to the exhaust. NOTE: K&N filters should only be used where extreme high end performance is required. They pass more air and more dirt than foam filters. They require frequent cleaning, are difficult to clean and oil and take an extraordinary amount of time to service properly. If you ride a lot in dusty conditions (and with the top of the air box drilled, you will not be operating in very wet conditions), you should have at leas two K&N air filters. One in the air box and one ready to put in the air box. You should have a K&N filter service kit and a semi-soft bristle brush to clean the filters with when you wash them.
There are 3 fuel control circuits within most carburetors: idle, mid-range and high speed
Start with idle; does the engine start and idle well? If yes, no changes are needed to the idle circuit. If no, can the idle be corrected by just adjusting the idle fuel mixture screw? If yes, make the adjustment and move to the next adjustment. Note; the engine has to be at normal operating temperature to accurately set the idle - if the fuel screw has to be turned out (counter clockwise) more than 4 full turn from lightly seated, increase the size of the pilot jet by 1 increment. The original pilot jet is a #38 - next larger one is probably #40 - there is probably no need to ever go larger than a #42 and very few modifications would ever require going that large.
With the engine idling satisfactorily, adjust the mid-range: the mid-range is for throttle openings from about 1/8 to 3/4 throttle. The adjustment is made by raising or lowering the slide needle. The typical slide needle is held in position with an E-clip and has 5 grooves the E-clip can be put in. Raising the clip leans the mixture and lowering the clip enriches the mixture. Warm the engine to normal operating temperature, ride the vehicle with a steady throttle setting in 3rd, 4th or 5th gear (typically about 1/2 throttle) - if the engine runs smoothly (no surging or blubbering), no adjustment to the needle is needed. If it surges, it's usually lean and the needle should be raised. If it blubbers (like it running with the choke on), then the needle needs to be lowered. If the slide needle in your carb is not adjustable, you will need to change needles or (if it's lean) you can shim the needle up using small thin washers. Once the setting is right, then move on to the main jet.
The main jet is the easiest adjustment to make. The carb does not have to be removed to change the main jet.
The main jet is for full throttle operation. The main jet is the only fuel control when the throttle is wide open and the engine is running near the top of it's RPM range. Get about 5 or 6 main jets size 150, 155, 160, 165 and 170. Warm the engine to normal operating temperature. Take the vehicle out where you can operate it in 5th gear at top speed. The engine should accelerate to maximum RPM cleanly to top speed and at top speed, it should not surge (lean) or blubber (rich). Jet up till it blubbers and then back down on the jet size till it runs without blubbering. You might need jets larger than 170 and 170 might be too big. Again, it's trial and error till you get it right.
Once you are done, you are not done - the jet requirements can change with fuel, air density, humidity and ambient temperature. You will have to fine tune each time you ride until all the circuits are working together. If you have a bog off idle, adjust the fuel screw out 1/8 turn at a time till the bog disappears and/or adjust the accelerator pump linkage so there is no lag in the accelerator pump shooting fuel into the air stream as the throttle is opened.
Always use fresh fuel, 92 octane or better, try to avoid ethanol blended fuel, try to always get fuel from the same source, avoid octane boosters and have fun.
@here2help I've got a decent stock of jets sounds like I need to go a little bigger on my main still and adjust the needle then. I got a 40 in the pilot and adjusted the mix screw to get my idle smooth.
@Here 2 help this thing is throwing me for a loop i got a 42 in the pilot and got the idle smooth but the needle I had to move the clip up one notch and got my midrange and I've tried goin from 148 up to 160 one jet at a time and I'm still boggin out past half throttle?
@Here 2 help it definatly gets worse I pulled the spark plug and cranked it and it seems to have weak spark to me and looks like it's been fouled alot so I went and picked up another plus a few spares today gonna put that in tomorrow and if it still seems weak I'll get a new coil before I mess with the jetting anymore
Hi guys, I was recently riding my 400EX when the chain popped off. Upon inspection the chain wrapped around the front sprocket remove chain put back on start getting ready to start the four-wheeler would only start with clutch pulled in when clutch released quad would immediately shut off even...
Was wondering if anyone had done a manual cam chain tensioner on the forums and had detailed instructions on how to do so? I've seen the instruction packet that comes with the tensioner Im lookin to buy but its pretty vague... Thanks for any help
I recently converted from two wheels over to four and acquired a 06 450. I loaded up into the back of my truck and everything was fine until i unloaded and the bike wont start!!!
I turn on the key and nothing. The neutral light only comes on if i turn on the headlights!!
Hi my carb keeps leaking fuel from the over flow and I rebuilt the carb twice and got a new oem float as well and it still leaks. I think the float valve isn’t seating correctly. Is there a way to fix the seating of the valve or adjust the float? Stock float doesn’t have adjustments. I’m ready...
Anyone know where I can get a free download? I had one a month or so ago on my computer but one day my computer flipped out and I lost it. I gotta put the top end of this 450 together (hopefully today) and I need some info. I've searched and searched this morning, but, I can't find one. Thanks!
A forum community dedicated to Honda TRX ATV owners and enthusiasts. Come join the discussion about reviews, modifications, classifieds, troubleshooting, maintenance, and more! Open to all models across the 500, 400, 300, and 200 series.